2018 Suzuki Vitara Service Manual Fuse Box
. 59K,76G,844-74E TABLE OF CONTENTS MAINTENANCE SERVICE RECORD WARRANTY POLICY BEFORE DRIVING STEERING COLUMN CONTROLS INSTRUMENT PANEL OTHER CONTROLS AND EQUIPMENT OPERATING YOUR VEHICLE DRIVING TIPS AND SAFE DRIVING INSPECTION AND MAINTENANCE EMERGENCY SERVICE BODY WORK CARE GENERAL INFORMATION SPECIFICATION. 59K,76G,844-74E.
59K,76G,844-74E FOREWORD IMPORTANT This manual is an essential part of your MARUTI SUZUKI INDIA LIMITED believes WARNING/CAUTION/NOTE vehicle and should be kept with the vehicle in conservation and protection of Earth's Please read this manual and follow its at all times. Please read this manual natural resources. Consult your may not be covered under warranty.
MARUTI SUZUKI dealer or qualified service technician for advice on w w w w w WARNING installing such mobile communi- cation equipment. MAINTENANCE SERVICE RECORD 59K,76G,844-74E MAINTENANCE SERVICE RECORD MODEL CHASSIS NO. DATE OF MILEAGE BATTERY DELIVERY (km) MAKE SR. NO /BATCH CODE OWNER’S NAME & ADDRESS TEL. ADDRESS/STAMP OF SELLING DEALER SELLING DEALER CODE SHOWROOM IMPORTANT INFORMATION TO CUSTOMER Dear Customer.
MAINTENANCE SERVICE RECORD 59K,76G,844-74E DATE OF KIND OF MILEAGE DESCRIPTION OF JOB NAME OF SERVICING JOB CARD MECHANIC’S SERVICE SERVICE (km) DEALER/MASS SIGNATURE F.free Service P.Paid Service W.Warranty. Maruti Suzuki vehicle distributed in India This warranty shall not apply to: by Maruti Suzuki and sold by an authorised Maruti Suzuki dealer (a) normal maintenance service required other than the three will be free, under normal use and service, from any defects in. This warranty is the entire written warranty given by Maruti destroyed the owner should consult the authorised Maruti Suzuki Suzuki for Maruti Suzuki vehicles and no dealer or its or his dealer from whom the vehicle was purchased for instructions agent or employee is authorised to extend or enlarge this concerning replacement of the “Owner’s Manual and Service. (Engine oil, Transmission oil, Brake oil etc.) are also as per specification. The method of examination for deciding the warranty of the parts will be at the sole discretion of Maruti Suzuki and it's dealer and results of the examination will be final and binding.
If after examination, the warrantable condition is not established, Maruti Suzuki and it's dealer has the right to charge all, or part of the cost of such examination. Maruti Suzuki dealer. Maruti Suzuki will not be responsible for any penalty that may be charged by statutory authorities on account of failure to comply with the EMISSION STANDARDS. Emission Warranty will not be affected on the change of owner, provided all the documents are available.
EMISSION WARRANTY 59K,76G,844-74E Annexure-A List of parts covered under Emission Warranty Fuel injection Assembly, Pressure Regulator, Throttle Body Assembly. Electronic Control Module (ECM). Intake Manifold. Distributor and internal parts. Ignitions coil. Canister Assembly. Vapour Liquid Separator.
Fuel Tank and Filler Cap. BEFORE DRIVING 76G-74E BEFORE DRIVING Fuel Recommendation.3-1 Immobilizer System. 3-2 Door Locks.3-4 Windows. 3-6 Mirrors.3-8 Front Seat Adjustment.3-9 Adjusting Seat Position.3-9 Adjusting Seatbacks.3-10 Seat Belts.3-11 Lap Belt (if equipped). MARUTI SUZUKI and Exposure to heat when fully fuelled in may not be covered under Warranty.
“ON” position. From the vehicle.
You need to make spare keys, contact your MARUTI SUZUKI dealer. The vehicle must Key Number: be programmed with the correct identifica- tion code for the spare keys. BEFORE DRIVING 76G-74E NOTE:. If you lose your Immobilizer ignition key, contact your MARUTI SUZUKI dealer as soon as possible to have the lost one deactivated, then have the new key made by them. other vehicles with immobilizer keys, keep those keys away. BEFORE DRIVING 76G-74E DOOR LOCKS 76G-03-005 76G-03-006 76G-03-007 Side Door Locks To lock a door from inside the vehicle, push Central door locking system (if equipped) To lock the driver's door from outside the vehicle: the lock knob down. Pull the lock knob up You can lock and unlock all doors simultan- a) Insert the key fully and turn the top of to unlock the door.
BEFORE DRIVING 76G-74E EXAMPLE TYPE-1 (ALTO) 76G-03-008 76G-03-009 NOTE: Child-Proof Locks (if equipped) Rearend Door Lock. Moving the lock knob on passenger's As illustrated, a child-proof lock is provided To unlock the door, insert the key into the door locks or unlocks the passenger's for both rear doors. BEFORE DRIVING 76G-74E WINDOWS TYPE-2 (ALTO K10) 76G-03-009A 76G-03-011 76G-03-012 Raise or lower the door windows by turning Electric window controls (if equipped) w w w w w WARNING the handle located on the door panel. The driver’s door has switches 1 & 2 to operate the driver’s window and front. BEFORE DRIVING 76G-74E 76G-03-014 76G-03-013 The driver’s window has an “auto-down” The driver’s door also has a lock switch for w w w w w WARNING the passenger’s window. When you push in feature for added convenience (at toll You should always push in the lock booths or drive-through restaurants, for the lock switch, the passenger’s window.
BEFORE DRIVING 76G-74E MIRRORS TYPE-1 (ALTO) TYPE-2 (ALTO K10) 76G-03-015 76G-03-017 76G-03-017A Inside Rearview Mirror Outside Rearview Mirrors To adjust the inside rearview mirror, move Adjust the outside rearview mirrors (with the the mirror up, down, or sideways to obtain help of control lever, if equipped), so that the best view. The seat seatback could move unexpectedly, causing loss of control. Make sure that the driver’s seat and seatback are properly adjusted before you start driving. 76G-03-018 76G-03-019A TYPE-2 (ALTO K10) TYPE-2 (ALTO K10) 76G-03-018A 76G-03-019B. 76G-03-022 sure that the seats are adjusted seat, move the seatback to the desired before the seat belts are fastened.
Position, and release the lever to lock the TYPE-2 (ALTO K10) seatback in place. 76G-03-023 3-10. BEFORE DRIVING 76G-74E SEAT BELTS 76G-03-026 76G-03-027 76G-03-028 w w w w w WARNING w w w w w WARNING w w w w w WARNING Seat belts are good help to protect. Never allow persons to ride in the tightly as is comfortable to provide occupants from injury or death in the cargo area of a vehicle. BEFORE DRIVING 76G-74E w w w w w WARNING w w w w w WARNING. Periodically inspect seat belt Be sure to inspect all seat belt assemblies for excessive wear and assemblies after any collision. Seat belts should be seat belt assembly which was in use replaced if webbing becomes frayed, during a collision (other than a very.
BEFORE DRIVING 76G-74E 76G-03-030 76G-03-031 76G-03-033 To fasten the seat belt, sit up straight and To reduce the risk of sliding under the belt well back in the seat, pull the buckle tongue during a collision, position the lap portion attached to the seat belt across your body of the belt across your lap as low on your and slide it into the buckle catch on the. BEFORE DRIVING 76G-74E 76G-03-034 76G-03-035 76G-03-036 To unfasten the belt, press the release To Adjust the Belt Seat Belt Inspection button on the buckle catch. Periodically inspect the seat belts to make. Pull the shoulder portion of the belt sure they work properly and are not upwards through the tongue plate. BEFORE DRIVING 76G-74E LAP BELT (if equipped) 76G-03-037 76G-03-038 76G-03-039 On this belt the adjuster is incorporated in To lengthen, release the tounge from the NOTE: the tounge unit.
Buckle unit, pull the tounge (adjuster) in To identify the center seat belt buckle catch the direction of the arrow, at right angles and tongue in the rear seat, 'CENTER'. STEERING COLUMN CONTROLS 76G-74E STEERING COLUMN CONTROLS Ignition Switch.4-1 Lighting/Turn Signal Control Lever.4-2 Hazard Warning Switch.4-5 Windscreen Wiper and Washer Lever.4-5 Horn.4-6 Electrical Power Steering (if equipped).4-7. MARUTI after the key is removed. SUZUKI dealer only. To release the steering lock, fully insert the key and turn it clockwise to one of the other positions. If you have trouble turning.
76G-04-004 76G-04-005 w w w w w WARNING CAUTION ALTO K10 TYPE-1. Never remove the ignition key while.
Do not use the starter motor for the vehicle is moving. The steering more than 15 seconds at a time. If wheel will lock and you will not be the engine does not start.
STEERING COLUMN CONTROLS 76G-74E ALTO K10 TYPE-2 ALTO K10 TYPE-2 ALTO 76G-04-005B 76G-04-006 76G-04-006B This control lever is located on the outboard With the headlights on, push the lever ALTO K10 TYPE-1 side of the steering column. Operate the forward to switch to the high beams (main lever as described below. STEERING COLUMN CONTROLS 76G-74E ALTO K10 TYPE-2 ALTO ALTO 76G-04-007 76G-04-008 76G-04-007B Turn Signal Operation ALTO K10 TYPE-1 ALTO K10 TYPE-1 With the ignition switch in the “ON” position, move the lever up or down to activate the left or right turn signals.
STEERING COLUMN CONTROLS 76G-74E WINDSCREEN WIPER AND HAZARD WARNING SWITCH WASHER LEVER ALTO K10 TYPE-2 76G-04-009 76G-04-010 76G-04-008B Lane Change Signal Push in the marked part of the hazard Windscreen Wipers Some times, such as when changing lanes, warning switch to activate the hazard. STEERING COLUMN CONTROLS 76G-74E HORN CAUTION EXAMPLE To prevent damage to the windscreen wiper and washer system components, should take following precautions:.
Do not continue to hold in the lever when there is no windscreen washer fluid being sprayed or the washer motor can be damaged. STEERING COLUMN CONTROLS 76G-74E ELECTRIC POWER STEERING (If equipped) 76G-04-013 Depending on specifications, your vehicle is equipped with electric power steering system to reduce the steering effort while driving. INSTRUMENT PANEL 76G-74E INSTRUMENT PANEL Instrument Panel.5-1 Instrument Cluster. 5-2 Warning and Indicator Lights. 5-4 Speedometer.5-7 Odometer/Tripmeter.
5-8 Tachometer (if equipped). 5-9 Fuel Gauge.5-9 High Engine Coolant Temperature Warning Light (Red Color).5-9 Glove Box.
Other switches (if equipped) 7. Heater control panel (if equipped) 8. Ashtray (if equipped) 9. Bonnet release (if equipped) 10.
Center ventilator 11. Side ventilator 12.
Side defroster 13. Glove box 14. Fuse box 76G-05-001 TYPE-2 (ALTO / ALTO K10) 76G-05-002.
INSTRUMENT PANEL 76G-74E INSTRUMENT CLUSTER (ALTO) 1 Speedometer 2 Odometer/Trip meter 3 Odometer/Trip meter selector knob 4 Fuel gauge 5 High Temperature Coolant warning lamp 6 Warning and indicator lights 76G-05-003. INSTRUMENT PANEL 76G-74E INSTRUMENT CLUSTER (ALTO K10) 1 Speedometer TYPE-1 2 Odometer/Trip meter 3 Odometer/Trip meter selector knob 4 Tachometer (if equipped) 5 Fuel gauge 6 High Temperature Coolant warning lamp 7 Warning and indicator lights TYPE-2 76G-05-004 76G-05-004A. If any of the following conditions occur, you should immediately ask your Remember that stopping distance may MARUTI SUZUKI dealer to inspect the be longer, you may have to push harder brake system. On the pedal, and the pedal may go. CAUTION your MARUTI SUZUKI dealer before you. Do not rely on the Oil Pressure drive the vehicle again.
Do not continue driving long with the Light to indicate the need to add oil. NOTE: problem with the emission control system. If the power steering system does not work Take the vehicle to your MARUTI SUZUKI properly, you will feel heavier to steer but dealer to have the problem corrected. You still will be able to steer.
INSTRUMENT PANEL 76G-74E SPEEDOMETER ALTO ALTO K10 TYPE-2 76G-05-011 Turn Signal Indicators When you turn on the left or right turn signals, the corresponding green arrow on the instrument panel will flash along with the respective turn signal lights. When you turn.
INSTRUMENT PANEL 76G-74E ODOMETER/TRIPMETER 76G-05-016 76G-05-014 76G-05-015 The odometer (2) records the total distance When the ignition switch is turned to 'ON' Push the selector knob for a little while the vehicle has been driven. The trip meter the display shows the odometer or trip (about 2 seconds) to reset the trip meter (3) can be used to measure the distance meter.
INSTRUMENT PANEL 76G-74E TACHOMETER (if equipped) FUEL GAUGE HIGH ENGINE COOLANT TEMPERATURE WARNING LIGHT (Red Color) 76G-05-013C 76G-05-018 The tachometer indicates engine speed When the ignition switch is in the “ON” 76G-05-019 in revolutions per minute. Position, this gauge gives an approximate When the ignition switch is turned to the indication of the amount of fuel in the fuel “ON”. INSTRUMENT PANEL 76G-74E GLOVE BOX HEADLIGHT LEVELING SWITCH Vehicle load Switch Position Condition Driver only Driver + 1 passenger (in front seat) Driver + 3 passenger No cargo Driver + 3 passenger 76G-05-022 76G-05-023 Cargo added To open the glove box, pull the latch lever. Level the headlight beam according to the To close it, push the lid until it latches load condition of your vehicle by turning this. HEATING SYSTEM (if equipped) a. Windscreen defroster outlet b. Side defroster outlet The heating system provides heating, c.
Side outlet demisting, and ventilation. Center outlet e. Floor outlet TYPE-1 (ALTO) 76G-05-025 TYPE-2 (ALTO / ALTO K10) 76G-05-024 76G-05-026 5-11. Four positions-OFF, LOW, MEDIUM and temperature. HEAT 4: Temperature-controlled For Type-2 (Alto / Alto K10) 76G-05-029 air comes out of the floor outlets.
Five Positions-OFF, LOW, MEDIUM LOW, MEDIUM HIGH and HIGH. “FRESH AIR”, the temperature control switch to a position other than “OFF”. Lever/knob to the desired temperature position, and the fan switch to “OFF”. Fresh air will flow through the vehicle when it is moving. 76G-05-034 TYPE-2 (ALTO/ALTO K10) 76G-05-035 5-13.
Moving the fan switch to a higher fan speed position increases heating efficiency. 76G-05-036 76G-05-038 TYPE-2 (ALTO / ALTO K10) TYPE-2 (ALTO / ALTO K10) 76G-05-037 76G-05-039 5-14. 76G-05-040 TYPE-2 (ALTO/ALTO K10) 76G-05-041 5-15. /knob to the desired temperature position, and the fan switch to “HIGH”.
When the windscreen has become clear, move the fan switch to the desired fan speed position. 76G-05-042 76G-05-044 TYPE-2 (ALTO / ALTO K10) TYPE-2 (ALTO / ALTO K10) 76G-05-043 76G-05-045 5-16. 76G-74E AIR CONDITIONING SYSTEM SYSTEM OPERATING INSTRUCTIONS (if equipped) Defrosting (ALTO / ALTO K10) (ALTO / ALTO K10) Move the function lever/knob to “DEFROST” and the air intake lever to “FRESH AIR”, the temperature control lever/knob to the desired temperature position, and the fan switch to “HIGH”. INSTRUMENT PANEL 76G-74E Maintenance (ALTO / ALTO K10) (ALTO / ALTO K10) If you do not use the air conditioner for a long period, such as during winter, it may not give the best performance when you start using it again. To help maintain op- timum performance and durability of your air conditioner, it needs to be run periodically. 76G-74E MEMO. OTHER CONTROLS AND EQUIPMENT 76G-74E OTHER CONTROLS AND EQUIPMENT Parking Brake Lever.6-1 Pedals.6-2 Gear Lever.6-3 Fuel Filler Cap.6-3 Folding Rear Seats.
6-5 Sun Visor.6-5 Interior Light Switch.6-6 Assist Grips. If the parking brake does not hold the vehicle securely or does not fully release, have your vehicle inspected immediately authorized MARUTI SUZUKI dealer. 76G-06-001 76G-06-002 The parking brake lever is located between w w w w w WARNING the seats. Brake Pedal 2 2 2 2 2 w w w w w WARNING The clutch pedal is used to disengage the Your MARUTI SUZUKI vehicle is equipped Do not “ride” the brakes by applying drive to the wheels when starting the with front disc brakes and rear drum brakes. GEAR LEVER FUEL FILLER CAP MANUAL TRANSMISSION Your vehicle is equipped with a manual TYPE-1 (ALTO / ALTO K10) ALTO transmission.
The gear change pattern for manual transmission is shown in the illustration. For details on how to use the. OTHER CONTROLS AND EQUIPMENT 76G-74E TYPE-2 (ALTO) EXAMPLE EXAMPLE 76G-06-007 76G-06-008 76G-06-006 The fuel filler cap is located on the left rear The fuel tank filler cap has a 'screw-on CAUTION ratcheting type' feature. Side of the vehicle. To unlock the fuel filler If you need to replace the fuel cap, lid, turn the key clockwise. OTHER CONTROLS AND EQUIPMENT 76G-74E FOLDING REAR SEATS SUN VISOR w w w w w WARNING EXAMPLE When returning a rear seat to the normal position, make sure that movement seatback unobstructed and the seatback is securely latched. W w w w w WARNING Luggage or other cargo should be stowed in the luggage compartment with the rear seat in an upright.
OTHER CONTROLS AND EQUIPMENT 76G-74E INTERIOR LIGHT SWITCH ASSIST GRIPS BONNET EXAMPLE 76G-06-013 76G-06-014 76G-06-015 This light switch has three positions which Assist grips are provided for passenger To open the bonnet: function as described below: convenience. 1) Pull the bonnet release handle located 1 The light comes on and stays on w w w w w WARNING on the outboard side of the driver’s side. OTHER CONTROLS AND EQUIPMENT 76G-74E FRAME HOOKS (If equipped) EXAMPLE EXAMPLE EXAMPLE 76G-06-016 76G-06-017 76G-06-018 2) Push the under-bonnet release lever 3) Continue to lift up the bonnet until it is Hooks are provided in both the front and high enough to support with the prop rear of the vehicle for use in emergency sideways with your finger, as shown in the illustration. OTHER CONTROLS AND EQUIPMENT 76G-74E CUP HOLDER (if equipped) TYRE CHANGING TOOLS Example 76G-06-019 76G-06-020 76G-06-021 The cup holder is provided in the center The jack is stowed in the luggage console (if equipped). Compartment behind the rear seat. To remove the jack, turn its shaft w w w w w WARNING counterclockwise and pull the jack out of the Do not use the cup holder to hold. ALTO 76G-06-024 76G-06-025 76G-06-022 w w w w w WARNING ALTO K10 The jack should be used only to change wheels.
It is important to read the jacking instructions in the EMERGENCY SERVICE section of this manual before attempting to use the jack. OTHER CONTROLS AND EQUIPMENT 76G-74E High mount stop lamp is provided with your vehicle and is fitted on back door. The stop lamp will glow as when the brake pedal will be depressed. To change the bulb of the stop lamp, remove the clips at both sides of the cover, by pressing the inner pin inside so that the clip gets loose and remove the bulb on. 76G-74E MEMO 6-11. OPERATING YOUR VEHICLE 76G-74E OPERATING YOUR VEHICLE Exhaust Gas Warning.7-1 Daily Inspection Checklist.7-1 Starting the Engine. 7-2 Using the Transmission.7-3 Braking.
7-4 Running-in.7-5 Catalytic Converter. 7-5 Improving Fuel Economy. 7-6 Trailer Towing.
OPERATING YOUR VEHICLE 76G-74E EXHAUST GAS WARNING DAILY INSPECTION CHECKLIST w w w w w WARNING with the engine running, make sure the air intake lever is set to “FRESH AIR” and the fan is at high speed. Avoid operating the vehicle with the 76G-07-002 rearend door open. OPERATING YOUR VEHICLE 76G-74E STARTING THE ENGINE Once a week, or each time you fill your fuel Before starting the engine: Starting a Cold Engine tank, perform the following under-bonnet 1) Make sure the parking brake is applied Engine which is started after 6 hours should checks: fully.
ALTO 76G-07-003. Make sure that the vehicle is completely GEAR MAXIMUM SPEED ALTO K10 stationary before you change into re- First 37 km/h verse. Second 66 km/h.
49 km/h 5th to 4th Any Speed OK Servo assisted brakes 76G-07-004 Your vehicle has servo assisted brakes ALTO K10 which works with the assistance of engine The distance needed to bring any vehicle vacuum. GEAR MAXIMUM SPEED to a halt increases with the speed of the vehicle. OPERATING YOUR VEHICLE 76G-74E RUNNING-IN CATALYTIC CONVERTER w w w w w WARNING CAUTION Even without reserve power in the The future performance and reliability brake system, you can still stop the of the engine depends on the care vehicle by pressing the brake pedal and restraint exercised during its early harder than.
OPERATING YOUR VEHICLE 76G-74E IMPROVING FUEL ECONOMY The following instructions will help you CAUTION improve fuel economy. To minimize the possibility of catalyst Avoid excessive idling: or other vehicle damage: If you are to wait for more than a minute. OPERATING YOUR VEHICLE 76G-74E TRAILER TOWING Your MARUTI SUZUKI is designed to carry people and a normal amount of cargo, not to tow a trailer.
Maruti does not recommend you use your vehicle to tow a trailer. Towing a trailer can adversely affect handling, durability, and fuel economy.
DRIVING TIPS AND SAFE DRIVING 76G-74E DRIVING TIPS AND SAFE DRIVING High Speed Driving. 8-1 Driving on Hills.8-1 Driving on Slippery Roads.8-1 Driving on Wet Roads.8-2 Do’s and Don’ts for Safe Driving.8-3. DRIVING TIPS AND SAFE DRIVING 76G-74E HIGH-SPEED DRIVING When driving at a high-speed, pay attention. When driving down a hill, the engine to the following: should be used for braking by shifting to.
Stopping distance progressively increases next lower gear. With vehicle speed. Do not use tyres other than those. With the chains on, drive only at slow may result from spinning the wheels specified by MARUTI SUZUKI.
Never and moderate speeds. Use different sizes or types of tyres.
This section contains basic rules for safe driving. Read it carefully for good understanding of the content so that you can enjoy safe and pleasant driving in your Maruti Suzuki vehicle. 76G-08-002 76G-08-003 Starting 2. Always follow other vehicles at a safe 1. DRIVING TIPS AND SAFE DRIVING 76G-74E 76G-08-005 76G-08-006 especially dangerous when the tyres are 5. The higher the speed, the narrower the worn, for they allow a larger skid. Driver’s visual range becomes.
In such a state, it is difficult to anticipate any Use foot brake in three stages hazard and the driver feels much (1) Warn the vehicle behind you. DRIVING TIPS AND SAFE DRIVING 76G-74E MARGIN FOR SAFETY It is important to allow yourself a margin for safety during driving so that you can cope with erroneous or unexpected driving of other drivers.
For that, observe the following. Drive at a safe speed.
INSPECTION AND MAINTENANCE 76G-74E INSPECTION AND MAINTENANCE Periodic Maintenance Schedule. 9-1 Alto.9-2 Alto K-10.9-6 Drive Belt.9-10 Engine Oil and Filter.9-11 Gear Oil. 9-14 Engine Coolant.9-15 Windscreen Washer Fluid. 9-18 Air Cleaner. MARUTI SUZUKI recommends that.
Do not touch ignition wires or other ignition system parts when starting maintenance on your MARUTI SUZUKI the engine or when the engine is vehicle be performed by MARUTI running, or you could receive an SUZUKI Authorised Dealer/Service electric shock. INSPECTION AND MAINTENANCE 76G-74E ALTO A.Adjust. I.Inspect and correct or replace if necessary. T.Tighten to specified torque. R.Replace or change.
O.Rotate L.Lubricate. Note: This table includes services as scheduled up to 80,000 km mileage. Beyond 80,000 km, carry out the same services at the same intervals respectively. INSPECTION AND MAINTENANCE 76G-74E Interval: This interval should be judged FREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST by odometer reading or months, km (x 1,000) whichever comes first. Months FUEL Air cleaner Paved-road Clean every 5,000 km. Replace every 40,000 km.
2018 Suzuki Vitara Service Manual Fuse Box Diagram
Dusty condition Clean every 2,500 km or as required. INSPECTION AND MAINTENANCE 76G-74E Interval: This interval should be judged FREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST by odometer reading or months, km (x 1,000) whichever comes first. Months WHEEL Tyres (air pressure, abnormal wear, crack, rotation) I&O I&O I&O I&O I&O I&O. INSPECTION AND MAINTENANCE 76G-74E Interval: This interval should be judged FREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST by odometer reading or months, km (x 1,000) whichever comes first.
Months ROAD TEST Operation of Brakes, Gear shifting & speedometer Body and Chassis noise AIR CONDITIONER (if equipped) Check belt tension Tighten compressor mounting bolts. INSPECTION AND MAINTENANCE 76G-74E ALTO K10 A.Adjust. I.Inspect and correct or replace if necessary. T.Tighten to specified torque.
R.Replace or change. O.Rotate L.Lubricate. Note: This table includes services as scheduled up to 80,000 km mileage. Beyond 80,000 km, carry out the same services at the same intervals respectively. INSPECTION AND MAINTENANCE 76G-74E. INSPECTION AND MAINTENANCE 76G-74E.
If you are in any way unsure of your the gas must be released from the ability to undertake a task, then do not absorber safely. Ask your dealer for start it but contact your MARUTI SUZUKI assistance. Dealer to perform the work for you.
The belt should also be examined to ensure that it is not damaged. If the belt needs to be replaced or adjusted, have it done by your MARUTI SUZUKI dealer.
76G-09-002 Water pump belt (A) 8 - 9 mm DEF: 7 –. INSPECTION AND MAINTENANCE 76G-74E ENGINE OIL AND FILTER EXAMPLE ALTO ALTO K10 76G-09-003 76G-09-004 Specified oil (1) Preferred Oil Level Check Be sure that the engine oil you use comes It is important to keep the engine oil at the. 76G-09-006 from children and pets. Refilling Continuous contact with used engine ALTO K10 Remove the oil filler cap and pour oil slowly oil may cause (skin) cancer. Through the filler hole to bring the oil level Brief contact with used oil may irritate to the upper limit on the dipstick. Tightening torque for oil filter tion or gasket damage. If you find any 1 turn or leaks or are not sure that the filter 14 Nm (1.4 kg-m, 10.5 lb-ft) has been properly tightened, have the vehicle inspected by your MARUTI SUZUKI dealer.
When adding gear oil, use the appropriate engine. MARUTI SUZUKI dealer. Viscosity and grade as shown in the chart 2) Clean casing around oil filler plug to below. We highly recommend you use API remove risk of any loose dirt or debris GL-4 SAE 75W-90 (1) gear oil. Gives proper protection against corrosion and rust. Failure to use the proper coolant can dam- 76G-09-011 age your cooling system.
Your MARUTI SUZUKI authorized dealer can help you ALTO EXAMPLE ALTO K10 EXAMPLE select the proper coolant. INSPECTION AND MAINTENANCE 76G-74E Coolant Level Check CAUTION CAUTION Check the coolant level at the reservoir To avoid damaging your cooling sys-.
The mixture you use should con- tank, not at the radiator. With the engine tem: tain 50% concentration of anti- cool, the coolant level should be between. Keep out of the reach of Coolant Replacement w w w w w WARNING children and animals. Trust this job to your Maruti Suzuki It is dangerous to remove the radia- Authorised Workshop.
Tor cap when the water temperature. 76G-09-016 76G-09-017 Check that there is washer fluid in the tank. ALTO K10 EXAMPLE Refill it if necessary. Use a good quality windscreen washer fluid, diluted with water as necessary. Remove carbon deposits with a wire or pin and adjust the spark plug gap. 76G-09-018 76G-09-019 CAUTION ALTO K10 The air cleaner element should be replaced every 40,000 km. More frequent replacement is necessary when drive.
Alto - 13.0–22.0 N-m (1.3–2.2 kg-m, “SPECIFICATIONS” section at the end 9.4–15.9 lb-ft) of this book. Alto K10 - 25 N-m (2.5 kg-m, 18.0 lb-ft). NOTE: Do not allow contaminants to enter When installation, make sure the wires, the engine through the spark plug couplers, sealing rubber of top cover and holes when the plugs are removed. MARUTI GENUINE brake fluid. Replacement does not solve the problem, w w w w w WARNING have the ignition wiring and other ignition system inspected by your MARUTI SUZUKI Failure to follow the guidelines below dealer.
Can result in personal injury or serious damage to the brake system. If not, have the brake disengaged with ignition switch in system inspected by your MARUTI SUZUKI 'ON' position). Should the light dealer. If you doubt the brake pedal for the come on, immediately ask your.
WARNING If you experience any of the following problems with your vehicle’s brake system, have the vehicle inspected immediately by your MARUTI SUZUKI dealer. Poor braking performance 76G-09-028 76G-09-027. Inspect your vehicle’s tyres periodically by inspected by your MARUTI SUZUKI dealer. Performing the following checks: 1) Measure the air pressure with a tyre gauge.
Adjust the pressure if necessary. Be sure to have tyres and and tyres can significantly change the wheel alignment checked periodically steering and handling characteristics by your MARUTI SUZUKI dealer. Of your vehicle.
Therefore, use only those wheel and tyre combinations 4) Check for loose wheel nuts. to 8.5 kg-m (61.5 lb-ft) in a crisscross In case of abnormal tyre wear or pulling instructions EMERGENCY fashion with a wrench as shown in the towards one side, have the wheel aligned SERVICE section in this manual) illustration. At Maruti Suzuki authorized workshop. MARUTI driving. SUZUKI authorized dealer.
Care and maintenance tips for tubeless 76G-09-035 tyres 1. Always maintain recommended inflation pressure. When checking or servicing the battery, disconnect the negative cable.
In case of any problem, please get in Be careful not to cause a short circuit touch with MARUTI SUZUKI authorised 76G-09-037 by allowing metal objects to contact dealer. INSPECTION AND MAINTENANCE 76G-74E FUSES w w w w w WARNING ALTO K10 ALTO To avoid harm to yourself or damage to your vehicle or battery, follow the jump starting instructions in the EMERGENCY SERVICE section of this manual if it is necessary to jump start your vehicle. TURN/BACK inspected by an authorized MARUTI c. STEERING SUZUKI dealer. Always use a MARUTI d.
CIGAR genuine replacement. Never use a e. STARTER FUSE substitute such as a wire even for a f. INSPECTION AND MAINTENANCE 76G-74E ALTO ALTO K10 ALTO K10 Fuse Box (under dashboard) Fuse Box (under dashboard) 76G-09-041A 76G-09-042 76G-09-042A 1. HEATER Fuse Box NOTE: 2. WIPER/WASHER The fuse boxes are located in the engine Alto K10 3. DOOR LOCK compartment and under the driver’s side of.
Have your indicates the need for an inspection of vehicle inspected immediately by your the electrical system. This should be MARUTI SUZUKI dealer. Carried out by your MARUTI SUZUKI dealer.
76G-09-045 NOTE: Make sure that the fuse box always carries spare fuses. INSPECTION AND MAINTENANCE 76G-74E 76G-09-046 76G-09-047 76G-09-048 Front Interior Light Headlights Front Clearance/Turn Signal Light, Side Press the front part of the lens toward you Turn Signal Light, rear Combination Open the bonnet. Disconnect the coupler. And pull down the lens. To install it, simply Light, Registration Plate Light. Trust this replacement job to your MARUTI Remove the lens by using a plain screw counterclockwise. To install a new bulb, SUZUKI authorised workshop.
Driver covered with a soft cloth. Push it in and turn it clockwise.
You can access the individual bulb holders as. Ktm sx 125 2018 repair manual. INSPECTION AND MAINTENANCE 76G-74E WIPER BLADES 76G-09-052 76G-09-054 76G-09-053 Rear combination light (tail, stop, turn Registration plate light If the wiper blades become brittle or signal, etc.) Turn the lens counterclockwise and pull it damaged, or make streaks when wiping, Undo the screws that secure the housing replace the wiper blades. Some wiper blades may be different from the ones described here depending on vehicle specifications. If so consult your MARUTI SUZUKI dealer for proper replacement method. W w w w w WARNING The left and the right wiper arm assemblies are different from each other. 76G-74E MEMO.
EMERGENCY SERVICE 76G-74E EMERGENCY SERVICE Jacking Instructions.10-1 Jump Starting Instructions.10-2 Towing. 10-4 Towing Hook (if equipped).10-4 Emergency Remedies.10-4 Warning Triangle.10-5. EMERGENCY SERVICE 76G-74E JACKING INSTRUCTIONS 76G-10-001 76G-10-002 76G-10-004 1) Park the vehicle securely on hard level ground.
2) Apply the parking brake firmly and change into 'R' (Reverse) gear. Choke the front and rear wheel diagonally opposite the wheel to be changed. 3) Switch on the hazard warning flasher if your vehicle is in or near traffic. If you. Never run the engine when the never allow passengers to remain in are in doubt, call MARUTI SUZUKI vehicle is supported by the jack and the vehicle. Authorized workshop.
EMERGENCY SERVICE 76G-74E 3) Make jump lead connections as follows: a) Connect one end of the first jump lead to the positive (+) terminal of the flat battery. B) Connect the other end to the positive (+) terminal of the booster battery. C) Connect one end of the second jump lead to the negative (-) terminal of the booster battery. Have the contact a professional service.
Your dealer vehicle inspected by your authorized can provide you with detailed towing MARUTI SUZUKI dealer. Instructions If the Engine is Flooded CAUTION If the engine is flooded with petrol, it may be hard to start. EMERGENCY SERVICE 76G-74E WARNING TRIANGLE 1) Turn off the air conditioner, if equipped. Engine until these problems have been EXAMPLE corrected. 2) Take the vehicle to a safe place and park. 3) If you do not find a leak, carefully add coolant to the reservoir and then the 3) Let the engine run at normal idle speed radiator, if necessary.
EMERGENCY SERVICE 76G-74E 76G-10-013 76G-10-014. Remove the warning triangle carefully from the cover as shown by arrow 1. Open both the reflector arms as shown by arrow and lock the arms with each other with the clip provided in the right arm. 76G-74E MEMO. BODY WORK CARE 76G-74E BODY WORK CARE Corrosion Prevention.11-1 Vehicle Cleaning.11-2. BODY WORK CARE 76G-74E CORROSION PREVENTION It is important to take good care of your the vehicle which are not well ventilated as possible. If these deposits are difficult to vehicle to protect it from corrosion.
To permit quick drying. Wash off, an additional cleaner may be Listed below are instructions for how to This information illustrates the necessity of. BODY WORK CARE 76G-74E VEHICLE CLEANING Store your vehicle in a dry, well- cleaner for tougher stains. If you use a w w w w w WARNING ventilated area. Fabric cleaner, carefully follow When cleaning the interior or exterior Do not park your vehicle in a damp, poorly manufacturer’s instructions and precautions. BODY WORK CARE 76G-74E Cleaning the Exterior When washing the vehicle, follow the 4) Once the dirt has been completely instructions below: removed, rinse off the detergent with CAUTION running water.
1) Flush the underside of body and wheel 5) After rinsing, wipe off the vehicle body It is important that your vehicle be housings with pressurized water to with a wet chamois or cloth and allow. GENERAL INFORMATION 76G-74E GENERAL INFORMATION Vehicle Identification.12-1. Whenever you have occasion to consult your MARUTI SUZUKI dealer, remember to identify your vehicle with this number. Should you find the number difficult to read, you will also find it on the. SPECIFICATIONS 76G-74E SPECIFICATIONS NOTE: Specifications are subject to change without notice.
ITEM: DIMENSIONS UNIT:mm ALTO (STD / Lx / Lxi) ALTO K10 (Lxi / Vxi) Overall length 3495 3620 Overall width 1475 1495/1475 (without side moulding) Overall height 1460 1460. SPECIFICATIONS 76G-74E ITEM: ELECTRICAL ALTO (STD / Lx / Lxi) ALTO K10 (Lxi / Vxi) Standard spark plug NGK-DCPR7E, BOSCH-YR7DC NGK KR6A-10 Battery 34B20L (27AH/5HR) 38B20L (28AH/5HR) Fuses See “INSPECTION AND MAINTENANCE” section Headlight 12V 55/60W Turn signal light 12V 21W. 76G-74E MEMO. 76G-74E MEMO. 76G-74E MEMO. 76G-74E MEMO.
Suzuki Vitara Service Manual Free Download
Owner's Manuals Important System Requirements for '24 Hour Online View' of owner's Information All online viewing of Suzuki service literature and manuals require a Windows based PC, or Laptop with Internet Explorer 10 or 11 to correctly view the information. This information is not viewable with Chrome, Firefox or Apple Safari. The 24 hour online view version of the manual is also not available for download and must be read during the available timeframe. The 24 hour time peroid starts when the order is placed. Please see ' ' for more information.